FiiO CLASS A Hi-Fi Headphone Preamp Black
The FiiO CLASS A Black is a fully discrete Class A desktop headphone amplifier and preamplifier built around a fully balanced differential architecture. Drawing on Toshiba twin transistors and Sanken audio devices, it delivers up to 4,000 mW + 4,000 mW of balanced output into 32 Ω loads while keeping the warm, analog character that defines Class A amplification. A custom 60 W toroidal transformer, 20,000 μF capacitor reservoir, and DC servo control anchor the signal path, giving the amplifier the headroom and quietness needed for both sensitive IEMs and demanding full-size headphones.
- Five gain levels (Low, Medium, High, Super High, Ultra High) plus ±10 dB bass and treble adjustment for tailoring any headphone load.
- Three headphone outputs — 6.35 mm, 4.4 mm balanced, and 4-pin XLR — plus RCA and XLR preamp outputs for system expansion.
- Inputs include 3.5 mm, RCA, 4.4 mm balanced, and XLR balanced, with 12 V trigger in/out for one-touch system power.
- Linear power supply with 60 W toroidal transformer and 20,000 μF Nichicon capacitor reservoir for clean, stable current delivery.
FiiO CLASS A Black — A Fully Discrete Class A Desktop Headphone Amplifier
The FiiO CLASS A Black is a desktop headphone amplifier and Hi-Fi preamplifier designed to bring the sonic character of analog high-fidelity to a modern listening setup. At the heart of the unit sits a fully discrete Class A transistor amplification stage, built from carefully selected audio transistors, resistors, and capacitors that are matched and tuned per channel. The result is a continuous, linear output that produces the warm, natural, and distinctly analog sound Class A operation is known for. The FiiO CLASS A Black is the right choice for listeners who want genuine Class A tonality with the headroom to drive everything from sensitive in-ears to power-hungry planar magnetics.
Standout Features — Discrete Transistor Topology and Balanced Differential Architecture
What separates this amplifier from typical integrated designs is its fully discrete Class A transistor circuit, where each stage is built from individual Toshiba twin transistors, complementary Toshiba audio devices, and Sanken Electric audio transistors rather than an op-amp or chip. The Toshiba devices contribute a warm, smooth low end and engaging vocals, while the Sanken transistors add precision, fast slew rate, and dynamic authority on complex passages. A fully balanced differential architecture runs the positive and negative signal paths separately for each channel, lowering distortion and widening the soundstage while supporting the 4,000 mW + 4,000 mW balanced output rating.
Power Supply and Amplification — Headroom for Any Headphone
A custom 60 W toroidal transformer with a continuous silicon-steel core, enameled copper windings, copper foil shielding, and a self-resetting thermal switch feeds a split regulated supply. The 20,000 μF Nichicon capacitor reservoir stores the energy needed for sudden dynamic peaks, so drums and orchestral tuttis hit with controlled, tight bass and a deep, quiet background. This linear supply architecture is what allows the amplifier to deliver its rated power consistently without falling back on switching noise.
- Balanced Output Power: 4,000 mW + 4,000 mW into 32 Ω — drives demanding planar magnetics and high-impedance dynamics with authority.
- Single-Ended Output Power: 2,850 mW + 2,850 mW into 32 Ω (6.35 mm) — comfortable headroom for most over-ear headphones.
- Power Supply: 60 W custom toroidal transformer with 20,000 μF Nichicon capacitor reservoir — clean, stable current for low-noise operation.
- Signal-to-Noise Ratio: ≥121 dB (A-weighted) — exceptionally quiet background that lets micro-detail emerge.
Connectivity and Control — Built for System Integration
Versatility is built into every input and output on the chassis. Four analog inputs — 3.5 mm single-ended, RCA single-ended, 4.4 mm balanced, and XLR balanced — pair with any source from a portable DAC to a full-size transport. Two line outputs (RCA and XLR) let the unit operate as a preamplifier into power amplifiers or active speakers, while three front-panel headphone outputs (6.35 mm, 4.4 mm balanced, and 4-pin XLR) cover the most common headphone terminations. A 12 V trigger input and output synchronizes power with upstream sources and downstream amplifiers for one-touch system control.
- Analog Inputs: 3.5 mm, RCA, 4.4 mm balanced, XLR balanced — accepts any source from portable players to balanced studio gear.
- Headphone Outputs: 6.35 mm, 4.4 mm balanced, 4-pin XLR — covers single-ended and balanced headphone terminations.
- Preamplifier Outputs: RCA single-ended and XLR balanced — drives power amps or active speakers for full system use.
- Gain Stages: Five levels — Low, Medium, High, Super High, Ultra High — matches output to IEMs, mid-impedance dynamics, and planars.
- Tone Controls: ±10 dB independent bass and treble adjustment — fine-tunes low- and high-frequency balance without changing source components.
Signal Integrity and Protection — Quiet, Stable, and Safe
A built-in high-precision DC servo feedback circuit continuously monitors and corrects output DC offset, protecting connected headphones while improving bass response and transparency. The amplifier achieves a total harmonic distortion plus noise figure below 0.00046% at the XLR output, with a noise floor under 3.7 μV (A-weighted) and a frequency response extending from 20 Hz to 95 kHz. Multiple protection circuits guard against DC output, power-input overcurrent, output overload, overvoltage, and thermal events on both the headphone stage and the transformer, so the unit can run continuously without risk to the headphones connected to it.
- DC Servo Control: Continuous output offset correction — keeps DC at zero for headphone safety and cleaner low frequencies.
- THD+N: <0.00046% at XLR output (1 kHz, -2 dBV into 10 kΩ) — vanishingly low distortion for transparent amplification.
- Noise Floor: <3.7 μV (A-weighted) — black background that reveals the smallest musical details.
- Frequency Response: 20 Hz – 95 kHz, attenuation <3 dB — extends well beyond the audible band for phase and transient accuracy.
Who Is It For — Audiophiles Driving a Wide Range of Headphones
The FiiO CLASS A Black is the right choice for desktop audiophiles who want a single amplifier that can handle an IEM collection today and a power-hungry planar tomorrow. Five gain levels and ±10 dB tone controls make it adaptable to sensitive in-ear monitors, mid-impedance dynamic headphones, and demanding orthodynamic designs without forcing a compromise. Its preamplifier outputs and 12 V trigger integration also suit listeners building a two-channel desktop system around active speakers or a separate power amplifier. The unit runs warm by design — Class A operation dissipates heat continuously — so it belongs on an open shelf with good ventilation rather than buried in a closed cabinet.
FiiO — Desktop Hi-Fi Systems Built Around Analog Character
FiiO designed the CLASS A as the headphone amplifier centerpiece of its retro-style desktop Hi-Fi system, where every component from source to DAC shares a unified size and design language so the components sit together as a matched stack. The Class A circuit itself draws on the brand's experience with portable players and DAC/amp combos, scaled up to a desktop form factor with a linear power supply, hand-calibrated transistor biasing, and audiophile-grade parts including WIMA film capacitors, ELNA audio capacitors, and high-precision MELF resistors. The result is an amplifier that aims to deliver the warmth and musicality of vintage analog gear with the connectivity and protection features expected from a modern desktop component.
Type
Headphone Amp, Hi-Fi Preamplifier
Inputs
Outputs
Jack 6,3 mm, Jack 4,4 mm, 4 Pin XLR, Balanced XLR, RCA, 12V Trigger
Analogue Inputs
Analogue Outputs
Headphone Output
Yes
Package Contents
Height (cm)
6.7
Width (cm)
21.3
Depth (cm)
23.9
Weight (g)
3500
Made in
China
Documents
Instructions for use
Manufacturer information
Safety instructions
Please refer to the user manual for the specific safety instructions for this product.
